Anais do Congresso Anual da ABM


ISSN 2594-5327

72nd ABM Annual Congress vol. 72, num.72 (2017)


Título

ESTUDO DA VARIAÇÃO DA DBCP E DO ÂNGULO DE SOLDAGEM EM CORRENTE PULSADA, CURTO CIRCUITO CONVENCIONAL E CURTO CIRCUITO CONTROLADO EM SOLDAGEM MIG/MAG

STUDY OF THE VARIATION OF THE CTWD AND WELDING ANGLE IN PULSED CURRENT, CONVENTIONAL SHORT CIRCUIT AND CONTROLLED SHORT CIRCUIT IN MIG / MAG WELDING

DOI

10.5151/1516-392X-30768

Downloads

Baixar Artigo 588 Downloads

Resumo

O objetivo desse trabalho é comparar três técnicas em soldagem MIG/MAG com baixa energia: Curto Circuito convencional, Curto Circuito Controlado (CCC) Soft e modo corrente Pulsada através de soldagens na posição vertical descendente e avaliando a geometria do cordão de solda, o acabamento superficial e os sinais de aquisição. Essas três técnicas tem como vantagem a soldagem em todas as posições e o uso de baixas energias, que otimizam seu uso em chapas muito finas e em de passes de raiz. Foram definidos alguns parâmetros constantes como velocidade de alimentação e velocidade de soldagem e a corrente média foi mantida aproximadamente igual. Os parâmetros trabalhados foram a Distância Bico de Contato a Peça (DBCP) e o ângulo de soldagem e foi utilizado o modelo experimental Fatorial Completo, resultando em 27 ensaios. A soldagem com CCC Soft manteve a qualidade em quase todas as soldagens enquanto o C.C convencional e a corrente pulsada tiveram resultados satisfatórios apenas em algumas condições. Os resultados apresentaram que as soldagens com CCC Soft mantiveram a a geometria e a energia aproximadamente iguais mesmo com a variação da DBCP e do ângulo, o que não aconteceu com as outras duas técnicas, e a corrente pulsada apresentou bons resultados apenas na posição 15 graus puxando.

 

The objective of this work is to compare three techniques in low energy MIG / MAG welding: Conventional Short Circuit, Short Circuit Controlled (CCC) Soft and current mode Pulsed through welds in the downward vertical position and evaluating the weld bead geometry, the finish and acquisition signs. These three techniques have the advantage of welding in all positions and the use of low energies, which optimize their use in very thin plates and in root passes. Some constant parameters were defined as feed rate and welding speed and average current was maintained approximately equal. The parameters worked were the Contact Tip to Work Distance (CTWD) and the welding angle and the full factorial experiment model was used, resulting in 27 tests. CCC Soft welding maintained the quality in almost all welds while conventional short circuit and pulsed current had satisfactory results under some conditions only. The results showed that the welds with CCC Soft kept the geometry and the energy approximately equal even with the variation of the DBCP and the angle, which did not happen with the other two techniques, and the pulsed current presented good results only in the position 15 degrees pulling.

Palavras-chave

MIG/MAG, Curto Circuito, CCC, Corrente pulsada

MIG/MAG, Short circuit, CCC, Pulsed Current

Como citar

Castro, Jamil Nobre de; Pinheiro, Bruno Ribeiro; Motta, Marcelo Ferreira. ESTUDO DA VARIAÇÃO DA DBCP E DO ÂNGULO DE SOLDAGEM EM CORRENTE PULSADA, CURTO CIRCUITO CONVENCIONAL E CURTO CIRCUITO CONTROLADO EM SOLDAGEM MIG/MAG , p. 2780-2791. In: 72nd ABM Annual Congress, São Paulo, 2017.
ISSN: 2594-5327 , DOI 10.5151/1516-392X-30768